于2021年9月7日发布
设计Builder_v7_Documentation_A4.pdf
设计Builder_v7_Documentation_Letter.pdf
Published on 02 March 2021
S63DownloadPackage(6.1.8)v1.1.zip
Published on 02 February 2021
ASHRAE 140 2017 Test Results For DesignBuilder V6.1.zip
ANSI/ASHRAE Standard 140-2017 (aka BESTEST) validation test results for DesignBuilder v6.1 with EnergyPlus v8.9. Sections covered:
2019年12月10日发布
设计Builder_v6_Documentation_A4.pdf
设计Builder_v6_Documentation_Letter.pdf
Published on 19 February 2019
DesignBuilder SBEM手册v6.1.8 Revison 2.PDF
设计Builder SBEM Manual describes the combination of the DesignBuilder graphical interface and the Simplified Building Energy Model (SBEM) that can be used for producing Energy Performance Certificates (EPCs) and BRUKL reports for showing compliance with Part L2 of the Building Regulations.
Published on 15 February 2019
设计Builder DSM Manual v6.1.8.pdf
The DesignBuilder DSM Manual describes the combination of the DesignBuilder graphical interface and the Dynamic Simulation Model (DSM) that can be used for producing Energy Performance Certificates (EPCs) and BRUKL reports for showing compliance with Part L2 of the Building Regulations.
Published on 22 January 2019
ASHRAE 140 2017 Test Results For DesignBuilder V5.5.zip
ANSI/ASHRAE标准140-2017 DesignBuilder v5.5的验证测试v5.5 v5.5 v8.6。涵盖的部分:
发布于2018年7月20日
设计BuilderLoadsCalculationComplianceASHRAE183_v6.pdf
This document describes DesignBuilder v6 compliance withANSI/ASHRAE/ACCA Standard 183-2007, Peak Cooling and Heating Load Calculations in Buildings Except Low-Rise Residential Buildings
Published on 29 May 2018
设计BuilderDSMManual_v5.4.0.021.pdf
Published on 28 May 2018
设计BuilderSBEMManualDB_v5.4.0.021.pdf
于2017年5月4日发布
DesignBuilder_v5.0_ASHRAE140-2014.ZIP
ANSI/ASHRAE标准140-2014设计Bubuilder v5.0的验证测试带有EnergyPlus v8.5。涵盖的部分:
于2016年11月1日发布
designbuilder-printable-documentation-v5.0-a4-pages.pdf
请记住,在决定打印之前,有超过1200页!
Published on 14 July 2015
designbuilder-printable-documentation-v5.0-letter-pages.pdf
Please bear in mind that there are over 1300 pages before you decide to print this!
Published on 11 January 2015
ISO_13790_ EN 15265_Report.pdf
Report on EN ISO 13790 Standard (2008) Tests for the calculation of energy use for space heating and cooling
Published on 23 January 2014
设计BuilderSBEMManual-v4.1-Jan-2014.pdf
Published on 03 February 2011
设计BuilderCFDValidationVsPhoenics.pdf
Inter-model validation report comparing DesignBuilder CFD with the general purpose Pheonics CFD software. Report prepared by Northumbria University.
2010年10月17日发布
3TC-Parameter-Identification-Report.pdf
A report detailing some further development of the 3TC (3 Time Constant) simulation method used in DBSIm
3tc-bsert-paper.pdf
详细描述了DBSIM中使用的3TC(3个时间常数)集总参数仿真方法背后的算法。